So put the bar over that suction cup screw and add a knob which will screw back in the backside of suction cup. There is a screw coming from the backside of the suction cup, the bar is supposed to be attached to that screw of the suction cup. Attach The Bar And Adjust The Bar Plates: Pick the slightly larger suction cup than the dent and apply glue that cane with the kit on the suction cup, then place it directly on the dent. Rub the alcohol on dented spot and clean it using a cloth. In this method, glue will be used, so make sure to clean the dented area very thoroughly by using the cleaning solution which is rubbing alcohol that cane with the kit. You will get a dent remover kit at $15-$30 on any website or hardware store. Remove A Dent With Suction Tools:īuy a dent remover kit that comes along with a bar, instead of a big and heavy-duty suction cup because the bar works well on stainless steel refrigerators. A popping-up sound might occur when it will become flat. And this way the stainless steel surface will contract and will return back to its normal shape. Over time, the thin icy sheet will thaw and evaporate. Remember that compressed air contents can be too icy to but your skin, so better wear protective gloves. And while spraying, keep the can nozzle 1” away from dents. This will form a thin icy sheet on the dented area. Next, hold the compressed air can upside and spray the compressed air at the dent. The dented part should be warm only, not too hot. Now set your hairdryer at the highest and blow hot air pointing at the dented area for 30 seconds. Take a damp sponge or cloth and clean the dented area on your stainless steel refrigerator to remove any buildup of grease and oil. You’ll heat a pop-up sound when the stainless steel has returned to its place. Now hold the dry ice with a little pressure against that dent and in a circular motion move it for 30 seconds-1 minute. It will make the dry ice application easier and the refrigerator won’t get scratched by the dry ice either. Since dry ice can burn your fingers’ skin, wear protective gloves, then put a dry ice piece on a soft dry cloth and wrap the dry ice piece. Keep blowing hot air on the dent for like 30 seconds or more until the dented part on stainless steel surface is warm enough, but not hot. Then blow hot air straight onto the dent to heat the dent. Now use your hairdryer and turn the dryer at high. Next, you should use a damp (not soggy) sponge or clean cloth to clean the dent to clean any buildup of grease or food on the stainless steel surface. And make sure to take the dry ice in a foam cooler so that it doesn’t evaporate. Purchase dry from a grocery shop or a local hardware shop.
STAINLESS STEEL REFRIGERATOR DENT REPAIR PROFESSIONAL
So, before you decide to pay a professional to help you to remove a dent from your stainless steel refrigerator, you should try all these methods explained below as step-by-step guides.
Heat the dented area until it is hot before applying the ice. Contact a professional appliance repair shop if the dent persists after three attempts to remove it. If the dent doesn't pop out, repeat the above steps.Ĥ. As the metal contracts from the cold, the dent may pop out. Remove the ice and wait for three to five minutes. Rub the ice in the dent in small circles. Immediately place a piece of dry ice against the dented area.
Turn the blow dryer onto the high setting, and heat the dented area of the fridge until the metal is hot.Ģ. Plug in a blow dryer in the outlet nearest your fridge. Put on work gloves to protect your hands. A large dent will most likely require professional repair, but if the dent is small, with no creases or deep corners, you might be able to remove it yourself.ġ. A stainless steel refrigerator is an expensive investment, and you want it to look good for as long as possible. Stainless steel refrigerators are very stylish, but they are also prone to dents and damage. Stainless steel refrigerators are an expensive investment.
0 kommentar(er)
